Gradient tempering process

A process for tempering a product made from a metal alloy that produces varying degrees of toughness throughout a cross section of the product is presented

Development of Surfaces Optically Suitable for Flat Solar Panels

Innovations in reflectometry techniques are described; and the development of an absorbing selective coating is discussed along with details of surface properties. Conclusions as to the parameterization desired for practical applications of selective surfaces are provided

An exactly size consistent geminal power via Jastrow factor networks in a local one particle basis

The accurate but expensive product of geminals ansatz may be approximated by a geminal power, but this approach sacrifices size consistency. Here we show both analytically and numerically that a size consistent form very similar to the product of geminals can be recovered using a network of location specific Jastrow factors. Upon variational energy minimization, the network creates particle number projections that remove the charge fluctuations responsible for size inconsistency. This polynomial cost approach captures strong many-electron correlations, giving a maximum error of just 1.8 kcal/mol during the double-bond dissociation of H2O in an STO-3G atomic orbital basis.Comment: Updated the original arXiv submission to include improvements resulting from journal peer review. 5 pages, 4 figures, 1 tabl

Application of single crystal superalloys for Earth-to-orbit propulsion systems

Single crystal superalloys were first identified as potentially useful engineering materials for aircraft gas turbine engines in the mid-1960's. Although they were not introduced into service as turbine blades in commercial aircraft engines until the early 1980's, they have subsequently accumulated tens of millions of flight hours in revenue producing service. The space shuttle main engine (SSME) and potential advanced earth-to-orbit propulsion systems impose severe conditions on turbopump turbine blades which for some potential failure modes are more severe than in aircraft gas turbines. Research activities which are directed at evaluating the potential for single crystal superalloys for application as turbopump turbine blades in the SSME and advanced rocket engines are discussed. The mechanical properties of these alloys are summarized and the effects of hydrogen are noted. The use of high gradient directional solidification and hot isostatic pressing to improve fatigue properties is also addressed

Spin-independent v-representability of Wigner crystal oscillations in one-dimensional Hubbard chains: The role of spin-charge separation

Electrons in one-dimension display the unusual property of separating their spin and charge into two independent entities: The first, which derive from uncharged spin-1/2 electrons, can travel at different velocities when compared with the second, built from charged spinless electrons. Predicted theoretically in the early sixties, the spin-charge separation has attracted renewed attention since the first evidences of experimental observation, with usual mentions as a possible explanation for high-temperature superconductivity. In one-dimensional (1D) model systems, the spin-charge separation leads the frequencies of Friedel oscillations to suffer a 2k_F -- 4k_F crossover, mainly when dealing with strong correlations, where they are referred to as Wigner crystal oscillations. In non-magnetized systems, the current density functionals which are applied to the 1D Hubbard model are not seen to reproduce this crossover, referring to a more fundamental question: Are the Wigner crystal oscillations in 1D systems non-interacting v-representable? Or, is there a spin-independent Kohn-Sham potential which is able to yield spin-charge separation? Finding an appropriate answer to both questions is our main task here. By means of exact and DMRG solutions, as well as, a new approach of exchange-correlation potential, we show the answer to be positive. Specifically, the v-representable 4k_F oscillations emerge from attractive interactions mediated by positively charged spinless holes -- the holons -- as an additional contribution to the repulsive on-site Hubbard interaction

Preparation of monotectic alloys having a controlled microstructure by directional solidification under dopant-induced interface breakdown

Monotectic alloys having aligned spherical particles of rods of the minor component dispersed in a matrix of the major component are prepared by forming a melt containing predetermined amounts of the major and minor components of a chosen monotectic system, providing in the melt a dopant capable of breaking down the liquid solid interface for the chosen alloy, and directionally solidfying the melt at a selected temperature gradient and a selected rate of movement of the liquid-solid interface (growth rate). Shaping of the minor component into spheres or rods and the spacing between them are controlled by the amount of dopant and the temperature gradient and growth rate values. Specific alloy systems include Al Bi, Al Pb and Zn Bi, using a transition element such as iron

Experimental assessment of periodic piezoelectric composite arrays incorporating an anisotropic passive phase

This paper discusses the experimental assessment of a number of piezoelectric composite array structures incorporating a novel passive phase exhibiting anisotropic elastic properties. The passive polymer phase has been designed to limit inter-element crosstalk by attenuating lateral propagation across the array aperture. A selection of water coupled linear array coupons, operating with a nominal 400 kHz fundamental thickness mode frequency, has been prepared comprising the novel anisotropic passive phase. As a control, comparisons are made to similarly configured devices employing isotropic filler materials. Scanning laser vibrometry and measurements of electrical impedance characteristic on the array substrate demonstrate that the fundamental thickness mode of the devices configured with anisotropic polymer fillers is not contaminated by parasitic modes of vibration. The reasons for this are explained by considering the dispersion characteristics of the substrate. Water coupled hydrophone measurements of array element directivity; transmit voltage response and subsequently efficiency calculations illustrate that the observed reduction in mechanical cross talk has not been achieved at the expense of element sensitivity. Finally, comparisons between the experimental data and the PZFlex derived array responses are made, with good corroboration demonstrate

Performance of periodic piezoelectric composite arrays incorporating a passive phase exhibiting anisotropic properties

This paper explores the minimisation of interelement cross talk in 1-D and 2-D periodic composite array structures through the incorporation of a passive phase exhibiting anisotropic elastic properties. Initially the PZFlex finite element code was used to monitor array aperture response as a function of material properties. It is shown that in array structures comprising passive polymer materials possessing low longitudinal loss and high shear loss, inter-element mechanical cross talk is reduced, without a concomitant reduction in element sensitivity. A number of polymer materials with the desired properties were synthesised and their elastic character confirmed through a program of materials characterisation. Finally, a range of experimental devices exhibiting improved directional response, as a result of a significant reduction in interelement cross talk, are presented and the predicted array characteristics are shown to compare favourably in each case

Random-phase-approximation-based correlation energy functionals: Benchmark results for atoms

The random phase approximation (RPA) for the correlation energy functional of density functional theory has recently attracted renewed interest. Formulated in terms of the Kohn-Sham (KS) orbitals and eigenvalues, it promises to resolve some of the fundamental limitations of the local density and generalized gradient approximations, as for instance their inability to account for dispersion forces. First results for atoms, however, indicate that the RPA overestimates correlation effects as much as the orbital-dependent functional obtained by a second order perturbation expansion on the basis of the KS Hamiltonian. In this contribution, three simple extensions of the RPA are examined, (a) its augmentation by an LDA for short-range correlation, (b) its combination with the second order exchange term, and (c) its combination with a partial resummation of the perturbation series including the second order exchange. It is found that the ground state and correlation energies as well as the ionization potentials resulting from the extensions (a) and (c) for closed sub-shell atoms are clearly superior to those obtained with the unmodified RPA. Quite some effort is made to ensure highly converged RPA data, so that the results may serve as benchmark data. The numerical techniques developed in this context, in particular for the inherent frequency integration, should also be useful for applications of RPA-type functionals to more complex systems.Comment: 11 pages, 7 figure

A theoretical analysis of a piezoelectric ultrasound device with an active matching layer

This paper investigates the use of magnetically active materials in the matching layer of a piezoelectric transducer. This then allows the performance of the device to be dynamically altered by applying an external field. The effect that this new matching layer has on the performance of a typical device is theoretically investigated here. It transpires that the additional flexibility of an active matching layer can be used to maintain the efficiency of the device as the external load is varied